Newcore Gold Ltd. announced positive results from four column tests completed as part of the ongoing metallurgical program at the Company’s 100%-owned Enchi Gold Project ("Enchi" or the "Project") in Ghana. An average gold recovery of 94.7% was achieved from column testwork completed on two composite samples from the Sewum Gold Deposit ("Sewum") and two composite samples from the Boin Gold Deposit ("Boin"). Highlights from Column Test Results: Four Column Tests Completed, Average Gold Recovery of 94.7% Achieved; A total of four column tests (two from Sewum and two from Boin) returned an average gold recovery of 94.7%, with a recovery range of 91.7% to 97.7%. Low Reagent Consumption; All samples showed modest cyanide consumption of less than 1 kilogram per tonne ("kg/t"), with a 3 kg/t lime (hydrated) addition to maintain a pH above 10.5. Further Metallurgical Testwork Ongoing: Another column test is underway on a composite sample from the Kwakyekrom Deposit. Additional bottle rolls and column tests will be completed on samples from each of the four deposits (Sewum, Boin, Nyam, Kwakyekrom) which comprise the Inferred Mineral Resource at Enchi. Metallurgical Testing Summary: A total of four composite samples, two from Boin and two from Sewum, were submitted for column testwork to the Intertek Lab located in Tarkwa, Ghana, approximately five hours by paved road from the Enchi Gold Project. Material for the metallurgical samples consisted of the remaining reverse circulation ("RC") chips collected during the 2020 - 2021 RC drilling program which had previously been provided to Intertek for bottle roll tests. Samples for metallurgical testing consisted of 5 kilogram ("kg") splits created using a riffle splitter of the remaining material from the RC drill chips and are considered representative. The samples were selected to represent the two largest deposits on the Project, Sewum and Boin, and consisted of blended oxide and transitional material. For each deposit, samples included a range of gold grades, weathering intensities, and came from various areas of the deposits. The first composite ("Composite 1") was prepared using six samples from two drill holes representing approximately one kilometre of strike length from Boin Central with a total weight of 15.9 kgs. The second composite ("Composite 2") was prepared using six samples from two drill holes spaced three kilometres apart from Boin North and South weighting 15.8 kg. The third composite ("Composite 3") was prepared using six samples from two drill holes over 200 metres of Sewum Ridge with a total weight of 16.0 kg. The fourth composite ("Composite 4") was prepared using six samples from two drill holes from Sewum CH and Extension spaced apart by 1.5 kilometres and weighted 17.6 kg. A size analysis was done on all the composite samples. The samples were tested at seven screen sizes and included analyses for percent mass. The samples were assayed for gold which showed that gold was present in all size fractions analysed. The distribution shows relatively consistent gold grades for all size fractions within a tight range of 0.80 grams per tonne gold ("g/t Au") to 1.57 g/t Au, with one outlier grading 2.85 g/t Au. Results include 40% to 50% passing 150 microns indicating that agglomeration is warranted, and each of the four composite samples were agglomerated at 20 kg/t of Portland cement. Using the results of the sizing and grading analysis, a head grade was calculated for each of the composite samples. The results were then compared to the head grade assays which were completed on the 50-gram subsamples. The results compared well for three of the composites (#1, #2 and #3), with a wider but acceptable range for Composite #4 (1.51 vs 0.90 g/t Au). A coarse subsample weighting one kilogram was prepared from each composite, with a five day coarse bottle roll then completed. Results ranged between 80.6% and 88.0%, with an average recovery of 85.3%. For Composite #1, 57.5% of the gold was recovered on the first day with this increasing consistently to 88.0% by the fifth day. For Composite #2, the recovery on the first day was 45.9%, increasing to 80.6% by the fifth day. For Composite #3, the dissolution curve was similar to Composite #2 with the recovery moving from 40% to 84.7% by the fifth day. Composite #4 had an initial day recovery of 50.5%, 62.1% for the second day, 69.8% for the third day, 71.9% for the fourth day, and 87.9% for the fifth day. In all cases leaching was ongoing after the five days with ultimate recoveries expected to continue to increase with additional time. Four 10 kgs closed-cycle column leach tests were conducted on the samples as received. The test charge was loaded into 150 mm in diameter by 1.5-metre-tall PVC columns. 10 kg of the individual samples were agglomerated in a rolling drum using Portland cement at a 20 kg/t addition rate and then allowed to air dry for three days. After the samples had been air dried, they were loaded into the columns with the columns tilted at an angle to avoid stacking before being set upright. The column was then allowed to sit for a day before the initial level was taken to determine the slump. The leaching parameters used in this column leach test included the addition of approximately 3 kg/t of lime which was blended into each feed solution and a cyanide concentration of 1,000 ppm. The initial feed solution was prepared by adding lime to tap water to obtain a solution pH of 11.00 followed by the addition of one gram of sodium cyanide per litre of solution with a solution application rate of 10L/h/m2 for all samples. The column testwork was conducted under a closed cycle for 60 days for Composites #2, #3, and #4 and 70 days for Composite #1. All solution samples were assayed for gold and pH and free sodium cyanide was analyzed and recorded. Leach residue was thoroughly washed, dried, screened and analyzed for gold by fire assay. The column tests are aimed at simulating the response to leaching of the sample with the emphasis on establishing the gold dissolution characteristics (rate and extent), reagent consumption, and the degree of slumping within the ore bed. All samples showed amenability to heap leaching, with recoveries achieving more than 90% after 60 days for Composites #2, #3, and #4. Composite #1 achieved a recovery in excess of 90% after an additional 10 days of leaching.