- Drillhole 2 has been completed at 443m depth; Brine sampling and geophysics are underway.
- Numerous brine aquifers* were intersected between 90m and 295m depth in drillhole 2.
- Both diamond drillholes, located 4km apart, were centred over significant geophysical targets in magnetotellurics (MT) that inferred a series of conductive brine bearing aquifers.
- Results and interpretations from drillhole 1 are expected in mid-February, with drillhole 2 results in late March.
*Cautionary Statement: The intersection of brines does not imply that the brines are lithium bearing. Chemical analysis from an independent laboratory will determine lithium concentrations in a brine.
Brine sampling*and downhole geophysics of the second drill hole is underway. Specific aquifers are being sampled using packer sampling, with intervals determined from the downhole geophysical and geological logs.
Lithium assay results with interpretations are expected from drillhole 1 in the coming weeks, with drillhole 2 lithium results in late March.
The second vertical diamond drill hole has been completed at 443.5 metres depth. Numerous brine aquifers varying in width from a few metres to 10 metres in width were intersected at 90m, 130m, 210m, 245m, and 295m. Running sands, favourable for brine aquifers, were intersected at these same levels. Increased salinity suggests a favourable zone from 210m to 270m.
Fine grained sediments with sandy layers were common from the top of hole to 205m depth with gravels, conglomerates and coarse alluvial fan material below this to the base of the hole. The geology intersected reflected the anticipated target sequence as its similar in profile to the producing sequences of Albemarle's nearby
The second hole will be cased, with slotted casing in favourable aquifers to allow for further sampling and monitoring. Large brine sample volumes (>20,000 litres) will then be pumped and stored. Bulk volumes of brine will be submitted for analysis and testwork with various direct lithium extraction (DLE) providers (refer ASX announcement dated
QXR Managing Director,
The sampling undertaken is quite specific, using a packer sampler to take samples over individual aquifers from 3m to 10m thick. Bulk samples will be sent for direct lithium extraction testwork once collected.
It's taking a little longer than anticipated to get assays and interpret those results due to end-of-year issues but It's a great start to this large target Liberty Lithium project."
Packer Sampling
Packer sampling, using "straddle" packers, are being utilised to sample specific aquifers downhole. Within the open drillhole, below the drill bit head, rubber stoppers are inflated either side of the specific aquifer between 3m to 10m, with intervals determined from the resistivity and gamma downhole geophysical log together with the geological log, where brines were identified (see Figure 2*).
Drillholes and Deal Terms
The first vertical diamond drill hole was completed at 369 metres depth in late
Drillhole 2 is located 4km to the south of drillhole 1 and both are centred over significant MT geophysical targets interpreted as inferring a series of conductive brine bearing aquifers at depth. Both holes are positioned within an extensive lithium brine surface anomaly of over 10km defined in auger samples (see image 4 below).
QXR has the ability to earn a 75% interest of the 102km2
*To view tables and figures, please visit:
https://abnnewswire.net/lnk/4461WOH7
About
Lithium portfolio: QXR's lithium strategy is centred around WA's prolific Pilbara province, where it has acquired a controlling interest in four projects through targeted M&A - all of which sit in strategic proximity to some of
Gold portfolio: QXR is also developing two
Contact:
Managing Director
T: +61-423-333-296
E: steve@qxresources.com.au
Executive Chairman
T: +61-411-545-262
Six Degrees Investor Relations
T: +61-423-755-909
Copyright (C) 2024 ABN Newswire. All rights reserved., source